Pylon Corrosion Protection: Morocco’s National Grid

Pylon corrosion protection usually means blasting, a primer, an anti corrosion coat and a finish coat. On Morocco’s national grid, contractor Net Elec has used one coat of Si-COAT 579 CM on steel pylons and concrete posts since about 2017, with no abrasive blasting.

End userONEE, Morocco’s national electricity and water utility
ContractorNet Elec, Casablanca
AssetsSteel pylons and concrete posts
ProductSi-COAT 579 CM, one coat
PreparationMinimal, with no abrasive blasting or profiling
ApplicationAirless spray or brush
First appliedAbout 2017, five years before the letter
SourceSigned letter from Net Elec’s president to CSL Silicones, July 2022

A contractor’s word, in writing

This case study is different from the others. It comes from the contractor who did the work, not from a test lab or a site report. In July 2022, Mohamed Haza, president of Net Elec in Casablanca, wrote to CSL Silicones about five years of using Si-COAT 579 CM on the Moroccan grid.

Net Elec’s end user is ONEE, which runs Morocco’s national power network. The assets are steel pylons and concrete posts. In short, this is the same kind of steel and concrete that carries power lines across Southern Africa.

Pylon corrosion protection letter from Net Elec to CSL Silicones about Si-COAT 579 CM on ONEE pylons and concrete posts
Net Elec’s signed letter to CSL Silicones, July 2022. Shared with permission from CSL.

Pylon corrosion protection: four coats replaced by one

Net Elec sets out the comparison plainly. A conventional anti corrosion system on a pylon needs four steps: blast, prime, an anti corrosion coat and then a finish coat. On top of that, it degrades over time.

By contrast, Si-COAT 579 CM goes on as one self priming coat. Net Elec notes it needs minimal surface preparation, with no abrasive blasting or profiling. As a result, they report savings in both time and labour, with the protection lasting.

Pylon corrosion protection without blasting

Blasting a pylon is slow and expensive. Crews have to contain the grit, work at height, and the steel needs a primer the same day before it flash rusts. Also, many pylons stand in farmland, bush or mountains, far from a compressor and a skip.

So a one coat system that goes on over hand or power tool cleaned steel changes the job. Crews take off loose rust and flaking paint, then apply 579 CM by brush or airless spray. Net Elec uses both methods. In their words, it stops rust creep.

Steel and concrete in one coating

Net Elec coated concrete posts as well as steel pylons. That matters on any network. Concrete poles crack and spall, and then the reinforcing steel inside starts to rust. Similarly, steel tower legs rust worst where they meet the concrete foundation.

At TSS we carry one continuous coat of 579 CM from concrete plinths straight onto the steel. However, the concrete must be free of laitance and wax or resin curing compound first, because 579 won’t bond to those. Our steel surface preparation guide covers the prep.

Pylon corrosion protection in Southern Africa

Southern Africa has thousands of kilometres of lines on steel towers. Near the coast, salt eats through the galvanising first, and then the steel. Inland, mines and power stations drop dust and acid fallout on lattice steel. Because of that, many towers reach a point where the zinc is gone and rust has started.

That is the point where pylon corrosion protection pays off. Coat the tower before section loss sets in, and you avoid replacing members later. Our article on transmission tower corrosion explains how towers fail. Likewise, the Reliant Energy towers in a tidal swamp show the same product under much harsher conditions.

What the letter covers, and what it doesn’t

The letter gives the end user, the assets, the product, the method and five years of service. It doesn’t give the number of pylons, the area coated or inspection photos. So we quote what Net Elec wrote and add nothing to it, as with all our CSL case studies.

Pylon corrosion protection FAQ

Does pylon corrosion protection need blasting first?

Not with Si-COAT 579 CM. It goes onto steel cleaned to SSPC SP2 or SP3 with hand or power tools. Even so, loose rust and flaking paint must come off first, and solvent cleaning alone is not enough.

Can the same coating go on concrete posts?

Yes. Net Elec used 579 CM on concrete posts for ONEE. Also, TSS carries it from concrete plinths onto steel, once laitance and curing compound are off.

How is it applied on a tower?

By brush or airless spray, in one coat. First, stripe coat edges, bolts and welds. Then apply one full coat of 0.2 to 0.5 mm dry (200 to 500 microns, 8 to 20 mil).

Where can I get Si-COAT 579 CM in Southern Africa?

Technical Solution Supplies distributes CSL Silicones products across Southern Africa, including the DRC and the Seychelles. For data sheets and pricing, request a quote with photos of your towers.

More case studies and articles

Proud exclusive distributor of CSL Silicones in Southern Africa.

Send us the problem

Photos and a rough size are enough to start, while drawings and specs can follow later. Then we come back with the right product and a quote.

Scroll to Top