

Silicone Coatings Corrosion Protection for Namibia
Silicone coatings corrosion protection suits Namibia better than most places. Mines, processing plants, ports and power lines all face a mix of wind blown sand, intense UV, coastal fog and process chemicals. Traditional epoxy systems have long been the default. However, they need blasting, several coats and long shutdowns, and they crack as steel heats and cools.
This article looks at what Namibian conditions do to steel, and how Si-COAT 579 CM from CSL Silicones handles them.
Why Namibia Is Hard on Steel
Namibia packs several corrosion threats into one country. On the coast at Walvis Bay and Lüderitz, regular Atlantic fog leaves salt on every surface. Inland, the sun is fierce and daily temperature swings are wide. Meanwhile, across the Namib, wind blown sand scours exposed steel and coatings.
Mining adds chemistry. The Tsumeb copper smelter captures its sulphur dioxide and turns it into sulphuric acid. That acid then travels by rail, roughly 600 to 670 km, to uranium mines such as Rössing, which uses sulphuric acid leaching to extract uranium. As a result, acid storage, handling and processing areas sit right in the middle of the mining economy.
Where Conventional Coatings Fall Short
Epoxy systems usually need abrasive blasting, a primer and one or two more coats. That means long application times, more labour and extended downtime, which is hard to arrange on remote sites. In addition, rigid epoxy cracks under the daily heat cycles of the desert. Once moisture or salt gets under the film, rust spreads out of sight.
What Silicone Coatings Bring to Corrosion Protection
Si-COAT 579 CM is a single component, moisture cure RTV silicone coating made by CSL Silicones. It goes on in one coat, with no separate primer or topcoat, over steel cleaned by hand tools, power tools or water jetting. For Namibia, its key strengths are:
- Sand. In ASTM D968 falling sand testing, it took 12 litres of sand per micrometre of film. In a separate sand drop test, the film was so elastic that the wear was too small to measure.
- UV. No degradation after 5,000 hours of accelerated UV weathering, with a colour change below 1 delta E.
- Salt. A pass in 3,000 hours of salt fog, and in the 36 month Florida Fence Test on the Atlantic coast with no rust creep.
- Heat cycles. With 180% elongation, the film moves with steel through hot days and cold nights instead of cracking.
- Chemicals. Excellent tolerance to airborne chemicals. Around acid, it handles vapour and occasional splash, but CSL did not design it for pooling or immersion.
Silicone Coatings Compared With Epoxy
| Feature | Epoxy Systems | Si-COAT 579 CM |
|---|---|---|
| Surface preparation | Abrasive blasting, usually | Hand tool, power tool or water jet cleaning |
| Coats | Primer plus one or two more | One coat, after a stripe coat |
| UV | Chalks without a topcoat | No degradation after 5,000 hours |
| Flexibility | Rigid, can crack | 180% elongation |
| Service life | Depends on preparation and exposure | About 20 years (benchmark) |
In documented projects, this adds up. For example, Florida Power and Light coated a large fuel oil tank in three weeks, against at least two months for a conventional system, at about 50% of the cost. Likewise, at Hellenic Petroleum near Athens, a 6,000 m² tank took about 89% fewer labour hours than their previous system.
Where to Use Si-COAT 579 CM in Namibia
Mines and processing plants. Structural steel, conveyors, tank exteriors and pipe racks, including around acid storage and leach areas, but not inside them. Our articles on mining corrosion protection and corrosion protection for copper mining go deeper.
Coastal plant and ports. Steel at Walvis Bay and Lüderitz that lives in fog and salt. For the harshest exposure, CSL pairs Si-COAT 579 CM with CSL 979 primer, a system that passed ISO 12944-6:2018 testing for C5 High.
Fuel and bulk storage. Tank shells, roofs and pipework. See our article on silicone coating for petroleum tanks.
Power. Transmission towers, substation steel and transformer casings. Read more on transmission tower corrosion and our high voltage insulator coatings.
Applying Si-COAT 579 CM
- Preparation: SSPC SP2 hand tool cleaning, SSPC SP3 power tool cleaning or SSPC SP12 water jetting to WJ-4. Remove loose rust, loose scale and flaking paint, and wash off salt and sand.
- Stripe coat: about 0.13 mm dry (5 mil) on edges, welds and bolts.
- Full coat: about 0.2 to 0.5 mm once dry (8 to 20 mil), roughly a third to three quarters of a litre per square metre, before losses.
- Conditions: surface between 5°C and 60°C and at least 3°C above the dew point. On the coast, that often means waiting until the morning fog has cleared and the steel is dry.
Silicone Coatings Corrosion Protection FAQ
Does sand abrasion damage silicone coatings?
Less than you might expect. Because the film is elastic, sand tends to bounce off rather than cut. In ASTM D968 falling sand testing, Si-COAT 579 CM took 12 litres of sand per micrometre of film. In a separate sand drop test, the wear was too small to measure.
Can it handle coastal fog at Walvis Bay?
Yes. It passed 3,000 hours of salt fog and the Florida Fence Test on the Atlantic coast. Just make sure the steel is dry and at least 3°C above the dew point when you apply it. For the harshest exposure, specify the CM System with CSL 979 primer.
Do silicone coatings give corrosion protection near acid?
For acid vapour and occasional splash, yes. That suits steel around acid storage and handling at mines and smelters, as our case studies show. However, it is not for pooling, immersion or the inside of acid tanks. In those areas, ask us and we will confirm suitability with CSL.
How long does it last?
On piping CSL coated at a Florida power plant in 2003, an inspection some 20 years later found the coating thickness unchanged. Of course, real life depends on preparation, thickness and exposure.
Technical Solution Supplies distributes CSL Silicones products across Southern Africa, including the DRC and the Seychelles, and that includes Namibia. Contact us about your project, or read the Si-COAT 579 CM FAQ.
Proud exclusive distributor of CSL Silicones in Southern Africa.

Pingback: Transmission Tower Corrosion: Why Africa's Power Grid Is at Risk - Technical Solutions Supplies