Distribution Transformer Corrosion: Saesa, Southern Chile

Distribution transformer corrosion was eating through Saesa’s tanks within six months on Chile’s salty southern coast. With Si-COAT 579 CM on the tanks and Si-COAT 570 HS on the insulation, no coated transformer has failed in three to four years, and insulator cleaning dropped from monthly to once every three years.

Distribution transformer corrosion before and after: a rusted pole transformer tank, then a unit coated in grey Si-COAT 579 CM
Before and after, from the applicator’s photos. The airless spray rig is in the background on the right.
OwnerGrupo Saesa, electricity distributor
RegionSouthern Chile, with head office in Osorno
AssetPole mounted distribution transformers
ProblemSalt corrosion destroying transformer tanks within six months
ProductsSi-COAT 579 CM on the tanks, Si-COAT 570 HS on the insulation
ApplicatorGrupo NTI, Chile
Started2018
ResultNo failures or deterioration on any coated transformer after three to four years. Insulator cleaning went from monthly to once every three years

Six months to rust through

Grupo Saesa runs transmission at 220 kV and 500 kV, and it distributes power across southern Chile. According to the applicator, its main distribution lines run along the southern coast. There, salt in the air and pollution land on everything.

The result was brutal. Saesa’s distribution transformers were deteriorating from salt corrosion within six months. That is a tank going from new to rusty in one winter. Once rust gets through a tank wall or under a gasket, oil weeps out and water gets in. After that, the unit is on borrowed time.

Why distribution transformer corrosion is a big deal

A distribution network has thousands of these units, and each one sits on a pole. So every failed transformer means a truck, a crane or bucket, a crew and an outage for the customers on that line. Similarly, every rusted tank that has to come down early is capital spent twice.

Also, the same salt that rusts the tank settles on the bushings. Then a wet morning turns it into a conductive film, and flashovers follow. That is why Saesa was washing insulators every month.

Stopping distribution transformer corrosion with one silicone system

In 2018, Saesa asked Grupo NTI, CSL’s applicator in Chile, for a fix. NTI coated the tanks with Si-COAT 579 CM and the insulation with Si-COAT 570 HS. In other words, one silicone family covered the whole unit.

On the steel, 579 CM goes over hand or power tool cleaned surfaces, with no blasting needed. Because it stays flexible, it moves with the tank as it heats up under load and cools at night. It also sheds water, so salt has less chance to sit on the steel.

Meanwhile, on the bushings, 570 HS keeps a water repellent layer on its surface. Water beads up instead of forming a film over the salt. As a result, leakage current stays low and flashovers don’t start.

Distribution transformer corrosion protection: a coated pole transformer back in service on a Saesa line in southern Chile
A coated transformer back in service on the pole.

Results after three to four years

According to NTI, not one transformer protected with the CSL system has failed or deteriorated after three to four years. Compare that with six months to rust through before. In addition, insulator cleaning went from once a month to once every three years.

That is 36 cleans cut to one. On a pole network, each clean is a crew on the road, so the saving adds up fast across a region.

Distribution transformer corrosion in Southern Africa

Southern Africa has the same problem on its own coasts. For example, pole transformers within a few kilometres of the sea in KwaZulu-Natal, the Eastern Cape and the Western Cape take salt spray every day. Similarly, the Namibian coast adds fog with very little rain to rinse it off. Inland, mines, smelters and power stations drop dust and acid fallout on the network.

On all of these, a distribution transformer coated in 579 CM and 570 HS lasts longer between visits. For new units, you can coat them in the workshop before they go up. For existing units, the coating goes on when they come down for maintenance. Our Algorta Norte transformer case study shows the same system at a desert mine in northern Chile.

Distribution transformer corrosion FAQ

How do you stop distribution transformer corrosion on the coast?

Coat the tank with a flexible silicone such as Si-COAT 579 CM, over steel cleaned to SSPC SP2 or SP3. At Saesa, tanks that rusted within six months showed no deterioration after three to four years.

Does the transformer tank need blasting first?

No. Hand or power tool cleaning is enough, as long as loose rust, flaking paint and oil come off first. Our steel surface preparation guide explains the prep.

Can you coat transformers that are already in service?

Yes, once they are out of service. The surface must be clean and dry, so crews take the unit off the line first. The coating is never applied to live equipment.

Where can I get Si-COAT 579 CM and 570 HS in Southern Africa?

Technical Solution Supplies distributes CSL Silicones products across Southern Africa, including the DRC and the Seychelles. For data sheets and pricing, request a quote with photos of your transformers.

More case studies and articles

Proud exclusive distributor of CSL Silicones in Southern Africa.

Send us the problem

Photos and a rough size are enough to start, while drawings and specs can follow later. Then we come back with the right product and a quote.

Scroll to Top