
A movement joint sealant has one job: stay bonded to both sides of the joint while the concrete opens, closes and shears with heat, cold and load. So the right choice is a soft, low modulus sealant with a tested movement rating, put in at the right depth over a backer rod. For horizontal concrete joints, a self levelling silicone such as CSL 316 SL does that job, with a movement rating of +100/minus 50%.
This guide is for engineers, contractors and maintenance teams across Southern Africa. It covers road and bridge joints, airport aprons, port yards, mine workshops and plant slabs, from the Copperbelt down to the coast.
What a movement joint actually does
Concrete moves all the time. First, it grows in the afternoon sun and shrinks again at night. Then it shrinks as it dries out over its first months. Slabs also deflect under trucks, and whole structures settle. A movement joint gives the concrete a planned place to move, so it does not crack somewhere you did not choose.
However, the joint is only half the system. Without a seal, water, sand and grit get in. Water softens the layers under the slab. Grit packs into the gap, so when the slab expands it pushes against stone instead of rubber, and the edges spall. That means the movement joint sealant protects the joint as much as the joint protects the slab.
Movement joint or expansion joint: is there a difference?
Movement joint is the umbrella term. Expansion joints, contraction or control joints, isolation joints and construction joints are all types of movement joint. In practice the names get mixed up on site and on drawings. What matters for the seal is how much the joint moves and in which direction, not what the drawing calls it. We explain why joints move in more detail in our guide to concrete joint movement.
How a movement joint sealant handles movement
Every sealant should carry a movement rating. That figure tells you how far the joint can open and close, as a percentage of its width, without the seal tearing or letting go. CSL 316 SL is rated +100/minus 50% to ASTM C719. So in that test, a 20 mm joint can stretch to 40 mm and close to 10 mm and still hold.
Modulus matters just as much. A high modulus sealant is stiff, so when the joint opens it pulls hard on the concrete edges. On a weak or dusty edge, either the bond line or the concrete gives way. By contrast, a low modulus sealant stretches easily and puts little stress on the bond. CSL 316 SL cures to a soft rubber of about 10 Shore A with 1000% elongation, so it moves with the joint instead of fighting it.
Sun is the third test. Exposed joints in the Kalahari, on the Highveld and along the Namib coast face hard UV and wide daily temperature swings. CSL 316 SL is stable from minus 60°C to 200°C, and CSL states it resists sunlight, ozone, rain and temperature extremes. Polyurethane, on the other hand, needs replacing far sooner than silicone in exposed conditions. We compare the two in our article on why polyurethane joint sealants keep failing.
Sizing the joint for the seal
Many joint failures come down to the installation, not the product. So get the geometry right first.
For CSL 316 SL, the joint should be 6 to 25 mm wide. The sealant goes in at about half the joint width in thickness, which works out at 6 to 12 mm. Then it sits recessed 6 to 12 mm below the surface, so tyres and wheels do not drag on it.
A backer rod sets that depth. Use polyurethane or expanded polyethylene foam rod, a snug fit in the joint. The rod also stops the sealant bonding to the bottom of the joint. That matters because a seal stuck on three sides cannot stretch freely, so it tears when the joint opens.
Finally, the engineer should size the joint width from the expected movement. Even the best movement joint sealant cannot save a joint that is too narrow for the movement it sees.
Installing a movement joint sealant step by step
- First, cut out old sealant and filler down to clean, sound concrete. New concrete needs at least 7 days before sealing.
- Then sandblast the top 25 mm of each joint face to clean the bonding surface.
- Next, blow out the joint with oil free air, working in one direction so the dust does not settle back.
- After that, push in the backer rod to the correct depth, with no gaps or stretched sections.
- Then pour the sealant. Because CSL 316 SL is self levelling, it flows out level in the joint. If you need to tool it, you have about 22 minutes.
- Finally, keep traffic off until it has cured. At 25°C and 50% RH it is tack free in 90 minutes and cured in 48 hours, with full properties at 7 days.
A primer is not needed on most substrates, but priming may be required on some. So run a trial bead and check adhesion after 7 days before you seal the whole job. Also note the sealant can go in at up to 50°C ambient; for cold conditions, check with us and CSL first.
Where this movement joint sealant fits
Because it is self levelling, CSL 316 SL is made for horizontal joints in concrete. Typical jobs across the region include:
- Road and bridge deck joints. In South Africa it conforms to the COTO specification used on SANRAL projects, although SANRAL does not approve individual products.
- Airport aprons and taxiways, because it keeps its seal after jet fuel exposure in a modified ASTM C719 test. See our airport apron article.
- Port yards and container terminals, from Walvis Bay to Maputo and Beira. Our harbour joint sealant article covers this in depth.
- Also mine workshop yards, plant slabs and process areas on the Copperbelt, in the Northern Cape and on the platinum belt.
- In addition, isolation joints in industrial slabs, around columns, plinths and loading bays.
On bridges, the joints are only part of the maintenance job, since the steel needs looking after too. Our bridge corrosion protection article covers that side.
For the track record, CSL reports a service record of more than 20 years in North America. Also, in 2021 a private label supplier to the Texas Department of Transportation ordered three truckloads, about 124,800 cartridges, for highway joints. CSL backs the product with a 10 year product warranty against material defects, on its standard terms.
When a self levelling movement joint sealant is the wrong choice
Be honest about the limits before you specify:
- Vertical and overhead joints, such as facades, brickwork, blockwork and precast panels. A self levelling sealant runs out of a vertical joint, so these need a non sag gun grade sealant.
- Joints narrower than 6 mm or wider than 25 mm, because they fall outside the CSL 316 SL design range.
- Saw cut floor joints under hard forklift wheels. A soft rubber does not support the joint edges, so those joints usually need a semi rigid filler instead. Our heavy traffic joint article explains why.
- Joints in permanent immersion or under constant water pressure. Send us the details first, before you specify anything.
Ready to reseal your joints?
If your joints are cracking, debonding or packed with grit, send us photos and the joint widths. We can suggest the right joint detail, send the TDS or a sample, or arrange a site visit. You can also browse our case studies and the CSL 316 SL FAQ first. Then get in touch with Technical Solution Supplies when you are ready.
Technical Solution Supplies distributes CSL Silicones products across Southern Africa, including the DRC and the Seychelles.
Movement joint sealant FAQ
Should you seal expansion joints?
Yes, in almost every exposed slab. An open joint fills with water and grit. Then, when the concrete expands, the grit pushes on the edges and they spall. A good movement joint sealant keeps the joint clean and still lets it move.
What is the difference between a movement joint and an expansion joint?
An expansion joint is one type of movement joint. Movement joint is the general term, and it also covers contraction, isolation and construction joints.
What does movement capability mean on a sealant?
It is how far a joint can open and close, as a percentage of its width, without the seal failing. CSL 316 SL is rated +100/minus 50% to ASTM C719.
How deep should a movement joint sealant be?
For CSL 316 SL, about half the joint width, so 6 to 12 mm thick. Then it should sit recessed 6 to 12 mm below the surface, over a snug backer rod.
How long does joint sealant last?
That depends on the chemistry and the exposure. CSL reports a service record of more than 20 years in North America for CSL 316 SL, and backs it with a 10 year product warranty against material defects on its standard terms.
Can you use self levelling sealant on vertical joints?
No. Self levelling sealant flows, so it runs out of a vertical joint. Use a non sag sealant for walls, facades and brickwork instead.
Questions about a joint on your site? Contact Technical Solution Supplies with photos and joint widths.
Proud exclusive distributor of CSL Silicones in Southern Africa.
