SI-COAT 579 CM: The Ultimate Anti-Corrosion Coating for South Africa’s Harsh Conditions

Anti-corrosion coating South Africa: corroded steel before Si-COAT 579
Before
Anti-corrosion coating South Africa: the same steel after Si-COAT 579
After Si-COAT 579. Photos: Premier Coatings Solutions, courtesy of CSL Silicones.

Choosing an anti-corrosion coating in South Africa means planning for very different conditions in one country. Salt air eats steel in Durban and Cape Town. The Karoo sun bakes coatings. Highveld storms soak and dry structures through summer, and mines add dust and acid mist on top.

This article looks at each of those conditions, and how Si-COAT 579 CM from CSL Silicones handles them, based on test results and documented projects.


Why South Africa Is Hard on Steel

The coast. Durban, Richards Bay, Gqeberha and Cape Town all sit in salt laden air. In KwaZulu-Natal, high humidity keeps that salt wet on the steel for much of the year. As a result, coastal steel often corrodes several times faster than the same steel inland.

The interior. In the Karoo and Northern Cape, UV is intense and the gap between day and night temperatures is wide. Organic coatings chalk and crack under that combination. Meanwhile, on the Highveld, summer afternoon storms wet structures that then dry in the sun, day after day.

Industry and mining. Around the coal power stations and petrochemical plants of the Mpumalanga Highveld, sulphur compounds in the air make rain and dew more aggressive. Mines and smelters add dust, acid mist and process chemicals. For more, see our articles on mining corrosion protection and corrosion protection for copper mining.


An Anti-Corrosion Coating Built for South Africa

Si-COAT 579 CM is a single component, moisture cure RTV silicone coating. It goes on in one coat, with no separate primer, mixing or topcoat. Here is how it answers each of those conditions:

  • Salt air. It passed 3,000 hours of salt fog testing, and three years on the Florida coast with no rust creep.
  • UV. CSL tests every colour to 5,000 hours of accelerated UV weathering, with a colour change below 1 delta E.
  • Heat cycles. With 180% elongation, the film moves with the steel instead of cracking.
  • Wet and dry cycles. The surface is water repellent, so rain beads and runs off rather than soaking in.
  • Old, rusty steel. It bonds to tightly bound rust and to sound existing coatings, so abrasive blasting is not needed. Our article on surface tolerant coating explains the preparation in detail.

What the Testing and Field Records Show

The Florida Fence Test. A large Florida power utility exposed 29 coating systems for three years on the beach at Melbourne Beach. The panels were pre-rusted, hand cleaned and scribed with an X to bare metal. Three coat epoxy and polysiloxane systems on blasted steel showed heavy rust creep and adhesive failure. Si-COAT 579, in one coat on the rusted steel, showed no rust creep, no blistering and no loss of colour.

Long service. In 2003, CSL coated about 24 km of process piping at a Florida power plant near the Atlantic coast. When CSL inspected it some 20 years later, the coating thickness measured the same as when it went on.

Faster work. At Hellenic Petroleum near Athens, a 6,000 m² crude oil tank took about 89% fewer labour hours than their previous conventional system. Read more in our article on silicone coating for petroleum tanks.


Applying an Anti-Corrosion Coating in South Africa

  • Preparation: SSPC SP2 hand tool cleaning, SSPC SP3 power tool cleaning or SSPC SP12 water jetting to WJ-4. Remove oil, salts, loose rust and flaking paint. Old coating that stays must pass the ASTM D3359 tape test at 4A or 4B.
  • Stripe coat: about 0.13 mm dry (5 mil) on edges, welds and bolts.
  • Full coat: about 0.2 to 0.5 mm once dry (8 to 20 mil), by spray, brush or roller.
  • Conditions: surface between 5°C and 60°C and at least 3°C above the dew point. On the KZN coast, that often means starting once the morning dew has dried.
  • Cure: tack free in 60 minutes, dry in 4 to 6 hours, full properties in 7 days.

For the harshest coastal exposure, CSL pairs Si-COAT 579 CM with CSL 979 primer. That system passed ISO 12944-6:2018 testing for C5 High.


Where It Should Not Be Used

Si-COAT 579 CM is for above ground, atmospheric exposure. It is not for immersion, buried steel, pooling liquids or the inside of tanks. For those, specify a lining system rated for immersion.


Anti-Corrosion Coating South Africa FAQ

Which anti-corrosion coating suits the South African coast?

For maintenance on existing coastal steel, Si-COAT 579 CM in one coat suits most structures. For the most severe exposure, such as steel right on the shoreline, the CM System with CSL 979 primer is the stronger choice.

Does Si-COAT 579 CM need sandblasting?

No. Hand tool, power tool or water jet cleaning is enough. It bonds to tightly bound rust and to sound existing coatings.

How long does it last?

On piping CSL coated at a Florida power plant in 2003, an inspection some 20 years later found the coating thickness unchanged. Of course, real life depends on preparation, thickness and exposure.

Can it handle sulphuric acid?

For acid vapour and occasional splash in acid plants, yes, as our case studies show. However, it is not for pooling or immersion. Ask us and we will confirm suitability with CSL.

Can it be used underwater?

No. It is not designed for immersion. Specify a lining system rated for immersion instead.


For more, see our guides to anti-corrosion coating for structural steel, bridge corrosion protection and corrosion protection methods, or read the Si-COAT 579 CM FAQ. Working further north? See our article on silicone coatings corrosion protection in Namibia.

Technical Solution Supplies distributes CSL Silicones products across Southern Africa, including the DRC and the Seychelles. Contact us about your project.

Proud exclusive distributor of CSL Silicones in Southern Africa.

2 thoughts on “SI-COAT 579 CM: The Ultimate Anti-Corrosion Coating for South Africa’s Harsh Conditions”

  1. Hi,

    I’m currently searching for an alternative to hot dipped galvanizing for our prop range, ideally the props to be dipped to coat internal and external surfaces including adjustment nuts and threads, it must also be resistant to the wear on the threads and adjustment nut, would SI-COAT 579 CM suit this application?

  2. Good Day Gavin,

    Thank you for reaching out to us, Silicone dipping is absolutely a viable option for props, and it brings several meaningful advantages. The coating offers strong chemical resistance, excellent hydrophobic properties and a consistent, attractive finish when applied by dip. Because it’s a high-solids formulation, it releases cleanly from threads, doesn’t become gummy and doesn’t interfere with adjustment mechanisms. Another practical benefit is that if the coating is damaged through normal handling, it can be touched up or repaired easily on-site without needing to redo the entire prop.

    It’s important to note that silicone works as a barrier coating and doesn’t provide the sacrificial protection associated with zinc. That said, it performs very well in environments where chemical resistance, surface cleanability and easy maintenance are key priorities. Many clients use it either as a standalone barrier in moderate-wear conditions or as an added top layer over existing zinc systems to enhance overall performance.

    A practical next step is an on-site test. Applying the coating to a small batch of props under real working conditions provides clear, direct feedback on performance. It also gives us the opportunity to visit, assess the environment and ensure the coating is matched correctly to their application. This approach keeps everything evidence-based and gives you the client confidence in the outcome.

    Please let us know if a onsite meeting at your establishment is possible to discuss further.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top