
Corrosion protection covers several distinct approaches, and South African asset owners rarely get a straight comparison between them. Galvanising, cathodic protection and protective coatings all claim to extend the life of exposed steel. However, each method solves a different problem. The right choice depends on the asset, the environment and the maintenance budget.
This article breaks down the main methods used across South African industry, explains where each one fits, and looks at how coating technology has changed in the last decade.
What Corrosion Protection Actually Means for South African Industry
Corrosion is an electrochemical process. Steel reacts with oxygen and moisture and slowly turns back into oxide. So every method works by interrupting one part of that reaction, whether through a physical barrier, a sacrificial metal layer or an electrical current.
South Africa tests all three approaches hard. Coastal regions bring salt-laden air. Mining and industrial zones bring acid process chemicals and airborne dust. Inland areas bring intense UV and wide daily temperature swings. As a result, a method that works well in one region can fail early in another.
The Main Corrosion Protection Methods South African Asset Owners Use
Galvanising: Protection Through Sacrificial Metal
Hot-dip galvanising coats steel in a layer of zinc. The zinc corrodes first, so it protects the steel underneath even where the coating gets scratched. That makes galvanising a strong option for new structural steel, fencing and components that can be dipped in a factory.
However, galvanising has real limits. The part has to fit in a dip tank, so it suits new fabrication far better than maintenance on site. In addition, the zinc layer slowly gets used up, and once it wears through, the steel underneath corrodes at a normal rate.
Cathodic Protection: Electrochemical Defence
Cathodic protection uses sacrificial anodes or an impressed electrical current to shift the electrochemical potential of a structure, which slows corrosion at the metal surface. Pipelines, buried tanks and marine structures commonly use it, because it protects steel that a coating alone cannot easily reach or maintain.
These systems need ongoing monitoring and periodic anode replacement, though. They also work best alongside a coating rather than on their own, since a coating cuts the current the system needs.
Protective Coatings: The Maintenance Friendly Option
Coatings remain the most common method for structures, tanks and equipment already in service. Unlike galvanising, a coating goes on site, on an asset that is already installed. Unlike cathodic protection, it needs no electrical monitoring.
For years, three coat epoxy systems dominated this category. Contractors blast the steel first, then apply a primer, an intermediate coat and a topcoat. The approach works, but it needs significant downtime, and the finished film is rigid. Rigid coatings crack with heat cycles, and once a crack forms, moisture and corrosive vapour reach the steel underneath.
Corrosion Protection Coatings Compared
Coating chemistry has moved on since three coat epoxy became the default specification. Asset owners now choose between several systems, each with different trade-offs in preparation, application time and long-term flexibility. The tables below compare the four systems South African specifiers meet most often.
Preparation and Application
| System | Surface Prep | Coats | Application Time |
|---|---|---|---|
| Three coat epoxy | Abrasive blast (Sa 2½) | 3 coats | Several days, with overcoat windows |
| Zinc-rich primer system | Abrasive blast (Sa 2½) | 2 to 3 coats | Several days |
| Polyurethane topcoat system | Blasting recommended | 2 coats | 1 to 2 days |
| Silicone (Si-COAT 579 CM) | SSPC SP2, SP3 or SP12, no blasting | 1 coat after a stripe coat | Dry in 4 to 6 hours |
Performance and Durability
| System | Flexibility | Chemical Resistance | UV Stability | Service Life |
|---|---|---|---|---|
| Three coat epoxy | Rigid, can crack | Strong until cracked | Chalks without a topcoat | Depends on preparation and exposure |
| Zinc-rich primer system | Rigid, zinc depletes | Good | Needs a UV topcoat | Depends on preparation and exposure |
| Polyurethane topcoat system | Moderate, can crack | Good | Strong | Depends on preparation and exposure |
| Silicone (Si-COAT 579 CM) | Elastomeric, 180% elongation | Salt, acid vapour and occasional splash | 5,000 hours, no degradation | About 20 years (benchmark) |
As the tables show, surface-tolerant elastomeric systems remove several of the barriers that traditional coatings carry, particularly the need for abrasive blasting and long shutdowns. For a deeper look at choosing between them, see our corrosion protection coating guide.
Why Silicone Coatings Are Changing Corrosion Protection for South African Steel
Elastomeric silicone coatings, such as Si-COAT 579 CM, tackle the failure mode that limits rigid systems. Because the film is elastomeric, it flexes with the steel instead of cracking as temperatures rise and fall. That matters in South Africa, where steel on mines, plants and the coast cycles through heat every day, on top of chemical or salt exposure.
CSL Silicones makes Si-COAT 579 CM as a single component RTV silicone. First, crews brush a stripe coat onto edges, welds and bolts. Then they apply one coat of about 0.2 to 0.5 mm once dry (8 to 20 mil). Preparation is SSPC SP2 hand tool cleaning, SSPC SP3 power tool cleaning or SSPC SP12 water jetting to WJ-4, with no abrasive blasting. As a result, it bonds to tightly adhered rust and sound old coatings, so crews can recoat live infrastructure without a long shutdown.
The evidence holds up. In a 36 month Florida Fence Test, it went onto hand tool cleaned rusted steel with no primer and showed no rust creep. It also passed 3,000 hours of salt fog and 5,000 hours of UV weathering with no degradation. Around acid, it handles vapour and occasional splash. Our service life benchmark is about 20 years, based on a CSL Florida power plant pipe coated in 2003.
For C5 sites, CSL pairs it with CSL 979 primer. That system passed ISO 12944-6:2018 testing for C5 High. One clarification matters here, though. Si-COAT 579 CM is for above ground atmospheric exposure, not immersion. For submerged steel, specify a system rated for the relevant ISO 12944 immersion category instead.
Corrosion Protection by Sector: Where South African Industries Need It Most
Different sectors face different corrosion problems, so the right coating usually follows the sector. Mines deal with acid, abrasive dust and plant that cannot stop for long recoats. We cover this in detail in our articles on mining corrosion protection and corrosion resistant coating for mining. On the Copperbelt of Zambia and the DRC, acid leaching adds even more pressure, as our article on corrosion protection for copper mining explains.
Bridges are a different problem. Access is tight, traffic management is costly, and blasting next to a live road brings safety and environmental issues. After the partial collapse of the Ezimbokodweni River Bridge on the N2, we looked at bridge corrosion protection and what it means for ageing structures.
Petroleum and chemical storage tanks face splash, UV and heat cycles together. Our article on silicone coatings for petroleum tanks covers why silicone suits tank exteriors. Coastal desert regions bring their own extremes, and we look at corrosion protection in Namibia separately. Power utilities face it too, from transmission tower corrosion to transformer casings, where Si-COAT 579 CM often works alongside our high voltage insulator coatings.
Across nearly every sector, structural steel faces the same problem: the specification rarely matches maintenance reality. Most specifications call for near-white metal blasting, Sa 2½ under ISO 8501-1. Yet most maintenance on steel in service only reaches hand or power tool cleaning, St2 or St3, which is roughly SSPC SP2 or SP3. Our article on surface preparation for corrosion maintenance deals with that gap, and our guide to anti-corrosion coating for structural steel applies it to structural work.
Choosing the Right Corrosion Protection Method for Your Asset
The right method depends on the asset type, the installation stage and the operating environment. New steel components that fit a galvanising bath benefit from zinc’s sacrificial protection. Buried pipelines and marine structures benefit from cathodic protection, ideally paired with a coating. Tanks, structural steel and process equipment already in service benefit most from a surface-tolerant coating that avoids long downtime.
So the question is rarely which single method is best overall. Instead, the useful question is which method fits the asset in front of you, given its history and its exposure.
Frequently Asked Questions
What is corrosion protection?
Corrosion protection is any method that slows or prevents the electrochemical breakdown of metal, usually steel, caused by oxygen, moisture, salts or acid chemicals. Common methods include galvanising, cathodic protection and protective coatings.
What are the main methods of corrosion protection used in South Africa?
South African industry relies mainly on hot-dip galvanising for new fabricated steel, cathodic protection for buried and submerged structures, and protective coatings for tanks, structural steel and process equipment already in service.
What is a corrosion protection specification, and why does it matter?
A specification sets the surface preparation standard, coating system, dry film thickness and expected service life for an asset. Specifiers use it to make sure the coating matches the conditions the asset will actually face.
Is a coating a better long-term option than galvanising or cathodic protection?
Not necessarily. Coatings suit assets already in service, galvanising suits new fabrication, and cathodic protection suits buried or submerged structures. In many cases, the best systems combine more than one method.
Where can businesses find corrosion protection coating suppliers in South Africa?
Technical Solution Supplies distributes CSL Silicones products across Southern Africa, including the DRC and the Seychelles. That includes Si-COAT 579 CM and the wider CSL range. Browse our corrosion protection articles or contact us for product and specification support.
Which South African industries face the greatest corrosion protection challenges?
Mining, bridges and petrochemical storage all face severe corrosion pressure. Mines deal with acid and abrasive dust. Bridges face structural movement and tight maintenance access. Petrochemical tanks face chemical splash combined with strong UV.
What is the difference between an Sa 2½ specification and a surface-tolerant coating?
Sa 2½ is near-white metal blast cleaning under ISO 8501-1, the standard most coating specifications assume. A surface-tolerant coating, by contrast, works on steel cleaned by hand or power tools, St2 or St3 under the same standard, roughly SSPC SP2 or SP3. That is what most maintenance on steel in service can realistically reach. Si-COAT 579 CM is one such coating.
Long-Term Protection Built Around the Right Method
Corrosion protection is not a single decision. It is a series of choices, made asset by asset, that account for installation stage, exposure and maintenance reality. Silicone coating technology has changed what is possible for existing infrastructure in particular, because it removes the blasting and downtime that traditional coatings demand.
To discuss options for your structural steel, tanks or process equipment, browse our corrosion protection articles, contact us, or read the Si-COAT 579 CM FAQ.
Proud exclusive distributor of CSL Silicones in Southern Africa.
